Victron MultiPlus 12/1600/70-16 Inverter/Charger PMP122160000

Inverter/Charger 1600VA, PMP122160000, Victron
multifunctional

Model No: MultiPlus 12/1600/70-16

The new style Multiplus was developed to replace the previous Multiplus Compact range. It simultaneously houses a powerful true sine wave inverter, a sophisticated battery charger with adaptive charging technology, and a high-speed AC transfer switch, all in one compact enclosure.

Models:

500VA, 800VA, 1200VA, 1600VA

Uninterruptible AC power (UPS function)

In the event of a grid failure or shore or generator power outage, the inverter inside the Multi automatically kicks in and moves the supply to the connected loads. This process is done so quickly (less than 20 milliseconds) that your computers and other electronic equipment continue to operate without interruption.

Remote Monitoring and Control

When paired with a GX device (e.g. Cerbo GX), you can use the free VRM app and the free VRM portal website to monitor and control your Multi and system or systems locally (LAN) or remotely over the internet from anywhere in the world. For multiple operating systems, access can be provided from a phone, tablet, laptop or computer. There's no limit to the levels of control, from setting up your multi to starting a backup generator and more..."

with arrow function, intelligent power management

MultiPlus is a sophisticated device that includes a powerful true sine wave inverter, adaptive charging technology, all in one compact enclosure.

It simultaneously houses the battery charger and high-speed AC transfer switch. Besides these basic functions, MultiPlus has the following

It also has a few advanced features outlined.

Parallel operation and three phase capacity

Up to six units of the Multi can operate in parallel, providing higher power output.

In addition to parallel connection, three units can be configured for three-phase output.

PowerControl - Dealing with limited generator, shoreside or grid power

Thanks to the Multi Control Panel, you can adjust the maximum generator or shore current. MultiPlus also takes into account other AC loads.

It uses all available extras for charging and prevents the generator or shore supply from being overloaded.

prevents.

PowerAssist – Increases the capacity of shore or generator power

This feature takes the PowerControl principle to a further level. Allows MultiPlus to be added to the capacity of the alternative source. Top

Where power is usually only required for a limited period of time, the MultiPlus can replace insufficient shore or generator power.

It allows immediate compensation with the power taken from the battery. When the load decreases, backup power is used to recharge the battery.

Four-stage adaptive charger and dual bank battery charging

The main output provides powerful charging to the battery system through an advanced “adaptive charging” software. Software adapts to battery condition

It fine-tunes the three-stage automatic process and adds a fourth stage for long-term buoyancy charging. adaptive

The charging process is explained in more detail under the Phoenix Charger data sheet and Technical Information on our website. MultiPlus,

as well as a second battery using the independent minimum charge output for a main engine or generator starter battery.

It can also charge.

High starting power

High inrush loads such as LED lamps, halogen lamps or power converters of electric vehicles

is required to start.

Look in

When Search Mode is "on", the power consumption of the inverter in no-load operation drops by approximately 70%. In this mode Multi,

When operating in inverter mode, it is turned off at no load or very low load and turns on for a short time every two seconds. output current

exceeds the set level, the inverter continues to operate. If it does not exceed, the inverter turns off again.

Programmable relay

By default, the programmable relay is set as alarm relay, that is, alarm or pre-alarm (the inverter is almost

too hot, input ripple almost too high, battery voltage almost too low).

is cut.

Remote on/off/charger on

Three pole connector.

On-site system configuration, monitoring and control feature

After installation, MultiPlus is ready to work.

Some settings can be changed with DIP switches.

500/800/1200 VA models: remote on-off / battery charging voltage / inverter frequency / search mode.

1600/2000 VA models: battery charging voltage / search mode.

For further settings use VEConfig or VE.Bus Smart dongle.

Inverter/Charger 1600VA, PMP122160000, Victron

Remote configuration and monitoring

Plug in Cerbo GX or another GX product to connect to the internet.

Process data can be stored and viewed free of charge on our VRM (Victron Remote Management) website.

When you connect to the internet, you can access systems remotely and make changes to settings.

This product Sent by the seller Yapıbahçe.
The price of the product you have examined is determined by the seller.